Technical Papers
Turbo Products
Note: files are in PDF format.
An Investigation of the Flow Distribution Inside a Radial Sidestream Inlet of a Centrifugal Compressor (Abstract - TP051)
Zheji Liu - D. Lee Hill - Gary Colby

Benefiting from Efficiency Improvements to Gas Compression (TP010)  
Harry Miller
Computational Modeling of Turbulent Flows Over Rough Surfaces (TP070)
Gocha Chochua - Wei Shyy
Damper Seal Comparison in a High-Pressure Re-Injection Centrifugal Compressor During Full-Load, Full-Pressure Factory Testing Using Direct Rotordynamic Stability Measurement (TP069)
J. Jeffrey Moore - Thomas Soulas
Design, Operation, and Maintenance Considerations for Improved Dry Gas Seal Reliability in Centrifugal Compressors  (TP134)
John S. Stahley

Dynamic Evaluation of a Three-Point Mount Base Plate for a Motor Driven Centrifugal Compressor Package (TP068)
Joseph Kubany - Joseph Tecza - Per Gustafsson

Experimental and Computational Study of a Radial Compressor Inlet (TP103)
Jay M. Koch - Peter N. Chow  - Brad R. Hutchinson  - Steve R. Elias

Experimental Results on a Rotatable Low Solidity Vaned Diffuser
(TP043)
J. Sorokes - J. Welch

Investigation of the Cirumferential Static Pressure Non-Uniformity Caused by a Centrifugal Compressor Discharge Volute (TP001)  
James M. Sorokes  -  Cyril J. Borer  -   Jay M. Koch

Noise Reduction of a Multistage Export / Reinjection Centrifugal Compressor Through the Use of Duct Resonator Arrays (TP081)
(Presented at GMRC 2005)
Zheji Liu - Mark Kuzdzal
On Reducing Piping Vibration Levels - Attacking the Source (Abstract - TP046)  
Zheji Liu - D. Lee Hill - R. Motriuk
On the Use of 5-Hole Probes in the Testing of Industrial Centrifugal Compressors (TP073)
José Gilarranz - Jason Kopko - Andrew Ranz - James Sorokes
Optimizing Peak Efficiency and Flow Range in Pipeline Centrifugal Stages (TP080) - (Presented at GMRC)
José Gilarranz - Jason Kopko - Andrew Ranz - James Sorokes
Performance Evaluation and Fluid Flow Analysis in Low Flow Stages of Industrial Centrifugal Compressor (Abstract TP056)
Y. I. Biba - D. A. Nye - Z. Liu

Power Turbine Life Assessment (TP004)  
Dresser-Rand

Range Versus Efficiency - A Dilemma for Compressor Designers and Users (TP071)
James Sorokes

Recent Experiences In Full Load, Full Pressure Shop Testing of a High Pressure Gas Injection Centrifugal Compressor (TP100)
James M. Sorokes  -  Mark J. Kuzdal -  Mark R. Sandberg  -  Gary M. Colby

Reducing Compressor Station Ambient Noise Level by Controlling Compressor Internal Noise Source (Abstract - TP048)  
 Zheji Liu - Bill Jahnke - Mike Marczak - Paul Kiteck
Rotordynamic Stability Measurement During Full-Load, Full-Pressure Testing of a 6000 PSE Re-Injection Centrifugal Compressor (Abstract - TP047)  
 J. Jeffrey Moore - Stephen T. Walker - Mark J. Kuzdzal
Sectional Modeling of a Centrifugal Compressor (TP054)
D. L. Hill

Statistical Analysis of Damper Seal Clearance Divergence and Impact Upon Rotordynamic Stability (TP076)
J. Tecza - T. Soulas - T. Eldridge
Three-Dimensional CFD Rotordynamic Analysis of Gas Labyrinth Seals (TP055)
J. J. Moore

Totally Enclosed Inline Electric Motor Driven  Gas Compressors (TP013)  
Harry Miller - Markus Ahrens - Anders t. Johnson - T. Kenton Flanery

 
 

Privacy Policy & Terms of Use | Site Feedback
© 2010 Dresser-Rand. All Rights Reserved.